注册 登录  
 加关注
   显示下一条  |  关闭
温馨提示!由于新浪微博认证机制调整,您的新浪微博帐号绑定已过期,请重新绑定!立即重新绑定新浪微博》  |  关闭

红烧鱼

linux & windows management

 
 
 

日志

 
 
关于我
mac

专注IT基础架构设计与运维。 欢迎给我留言,或邮件沟通zjwsk@163.com

网易考拉推荐

HPUX11i上用make_tape_recovery恢复带进行磁带引导还原系统  

2008-07-04 14:43:53|  分类: HPUX |  标签: |举报 |字号 订阅

  下载LOFTER 我的照片书  |
前提条件:
make_tape_recovery -A操作成功。

操作步骤:
1,重启系统,自检通过后在十秒中断处中断,如下所示:
Firmware Version  43.43
Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
   (c) Copyright 1995-2002, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
  Processor   Speed            State           CoProcessor State  Cache Size
  Number                                       State              Inst    Data
  ---------  --------   ---------------------  -----------------  ------------
      1      440  MHz   Active                 Functional         512 KB   1 MB
      3      440  MHz   Idle                   Functional         512 KB   1 MB
      5      440  MHz   Idle                   Functional         512 KB   1 MB
      7      440  MHz   Idle                   Functional         512 KB   1 MB
  Central Bus Speed (in MHz)  :        120 
  Available Memory            :    4193284  KB
  Good Memory Required        :      18880  KB
   Primary boot path:    0/0/2/1.6          
   Alternate boot path:  0/0/2/0.6          
   Console path:         0/0/4/0.0          
   Keyboard path:        0/0/4/0.0          
 WARNING:  The non-destructive test bit was set, so memory was not tested
            destructively.  Information only, no action required.

Processor is starting autoboot process.
To discontinue, press any key within 10 seconds.
Boot terminated.
2,通过“sea IPL”命令搜索可引导设备,找到磁带机的硬件路径地址0/0/1/0.0
3,通过磁带机引导,过程如下:
Main Menu: Enter command or menu > bo 0/0/1/0.0
Interact with IPL (Y, N, or Cancel)?> n
Booting...
Boot IO Dependent Code (IODC) revision 1

HARD Booted.
ISL Revision A.00.44  Mar 12, 2003
ISL booting  hpux (;0):INSTALL
Boot
: tape(0/0/1/0.0.0.0.0.0.0;0):WINSTALL
11751424 + 1970264 + 2631464 start 0x200d68
 

alloc_pdc_pages: Relocating PDC from 0xffff800000 to 0x7eb00000.
4,加载内核成功后,有如下显示:
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 4.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.
td: claimed Tachyon TL/TS Fibre Channel Mass Storage card at 1/2/0/0
    System Console is on the Built-In Serial Interface
    Swap device table:  (start & size given in 512-byte blocks)
        entry 0 - auto-configured on root device; ignored - no room
WARNING: no swap device configured, so dump cannot be defaulted to primary swap.
WARNING: No dump devices are configured.  Dump is disabled.
Starting the STREAMS daemons-phase 1
Create STCP device files
Starting the STREAMS daemons-phase 2
          $Revision: vmunix:    vw: -proj    selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108'  Wed Nov  8 19:24:56 PST 2000 $
Memory Information:
    physical page size = 4096 bytes, logical page size = 4096 bytes
    Physical: 4194304 Kbytes, lockable: 3203460 Kbytes, available: 3693540 Kbytes
=======  06/21/07 02:21:21 EDT  HP-UX Installation Initialization. (Thu Jun 21
         02:21:21 EDT 2007)
         @(#) Ignite-UX Revision C.6.1.44
         @(#) install/init (opt) $Revision: 10.303 $
       * Scanning system for IO devices...
       * Querying disk device: 0/0/2/1.6.0 ...
Recovery tape created from system: 4000new on Thu Jun 21 12:51:03 2007

WARNING: The configuration information calls for a non-interactive
         installation.
         Press <Return/Enter> within 10 seconds to cancel batch-mode installation:
       * Using client directory: /var/opt/ignite/clients/0x00306E1345B1
       * Checking configuration for consistency...
NOTE:    Free space (4129584KB) in "/var" where /var/adm/crash is located is
         less than system memory (4194304KB). This should be enough space to
         capture at least a single dump (and likely more than that if the dump
         is selective and/or compressed) in the event of a system crash.
         Additional space may be required to uncompress the dump in order to
         analyze it and to save multiple dumps. You can increase the size of
         the "/var" volume on the "File System" tab when using the advanced
         user interface.
WARNING: The disk at: 0/0/2/1.6.0 (HP_36.4GST336752LC) appears to contain a
         file system and boot area.  Continuing the installation will destroy
         any existing data on this disk.
         Press <Return/Enter> within 10 seconds to cancel batch-mode installation:
         Really cancel non-interactive install and start the
         user-interface? ([y]/n): y
       * Setting keyboard language to: PS2_DIN_US_English.
NOTE:   
         The console firmware terminal type is currently set to "vt100". If you
         are using any other type of terminal you will see "garbage" on the
         screen following this message.
         If this is the case, you will need to either change the terminal type
         set in the firmware via GSP (if your GSP firmware version supports
         this feature), or change your terminal emulation to match the
         firmware. In either case you will need to restart if your terminal and
         the firmware terminal type do not match.
         Press the 'b' key if you want to reboot now.
        
Recovery tape created from system: 4000new on Thu Jun 21 12:51:03 2007
5,通过手工中断,来到和光盘引导相同的安装界面:

             Welcome to the HP-UX installation/recovery process!
  Use the <tab> key to navigate between fields, and the arrow keys
  within fields.  Use the <return/enter> key to select an item.
  Use the <return/enter> or <space-bar> to pop-up a choices list.  If the
  menus are not clear, select the "Help" item for more information.
  Hardware Summary:         System Model: 9000/800/N4000-44
  +---------------------+----------------+-------------------+ [ Scan Again  ]
  | Disks: 1  ( 33.9GB) |  Floppies: 0   | LAN cards:   5    |
  | CD/DVDs:        0   |  Tapes:    1   | Memory:    4096Mb |
  | Graphics Ports: 0   |  IO Buses: 4   | CPUs:        4    | [ H/W Details ]
  +---------------------+----------------+-------------------+
                       [      Install HP-UX       ]
                       [   Run a Recovery Shell   ]
                       [    Advanced Options      ]
                       [  Read Sys-Admin Message  ]
                [  Reboot  ]                              [  Help  ]
6,按需求进行安装即可。
注:本文来自于网络
  评论这张
 
阅读(896)| 评论(0)
推荐 转载

历史上的今天

在LOFTER的更多文章

评论

<#--最新日志,群博日志--> <#--推荐日志--> <#--引用记录--> <#--博主推荐--> <#--随机阅读--> <#--首页推荐--> <#--历史上的今天--> <#--被推荐日志--> <#--上一篇,下一篇--> <#-- 热度 --> <#-- 网易新闻广告 --> <#--右边模块结构--> <#--评论模块结构--> <#--引用模块结构--> <#--博主发起的投票-->
 
 
 
 
 
 
 
 
 
 
 
 
 
 

页脚

网易公司版权所有 ©1997-2017